Wet sand area with a small sanding block in circular motions until smooth, then move to 600 grit and repeat. As you spray on your sealant, make sure that the entire surface of your marble is wet. You could also use a silicone spray when you’re done to help it shine and protect it from staining.


Product Emp Easy Marble Polish

poiish marbie

If you are not sure how much polish to apply, start with a little and add more as needed. If this does not give you satisfactory results, then you would need to go to the next step.

You don’t want to risk getting the sealant that’s seeped into the surface wet while it’s still fresh.


Homemade Marble Polishing Paste

If neither of these products works, cultured marble can be wet sanded using 1,000-grit wet/dry sandpaper. A poultice will remove stains that have settled into the porous surface of your marble.


Productcategory Polishing Products

productcategory poiishing products

What a polishing powder consists of are very fine abrasive grains that when applied through buffing create a high gloss.

Don’t seal cultured marble because it’s stronger and doesn’t need a sealant. Make a paste, cover the entire surface and let it dry overnight. P21 is a polishing paste that can be used to polish out etch marks in marble, as long as they are not too deep. Vinegar stains happen from acid eating into the marble and then dust penetrating the “bald” porous surface. These products can greatly enhance the look of moderately dull marble surfaces with regular use. Keep in mind that if you use a poultice you will need to wait at least 24 hours to continue to the next step.

Maintain the shine of your marble between polishings by running a clean, dry dust mop or soft cloth over the surface. If the scratches are very small and only on the surface, they can sometimes be buffed out with a soft cloth and a good cleaning. Allow the marble to dry for a minimum of three hours before moving to the next step. Spray this mixture on the marble surface and gently wipe it with a dry rag.


Marble Polishing

product emp easy marbie poiish

I have a culture marble bath room sink which is getting dull. Polishing marble is an easy task that you can do as often as once a month to keep your marble looking lustrous. It should be noted that exposure to tin oxide can result in mild irritation to the eyes, skin and mucous membranes and may also lead to pulmonary problems if inhaled so rubber gloves should be worn when using this to polish marble. If your cultured marble still has stains or shows damage, you can polish it with a buffing compound and then again with a polishing compound. Start in a corner and work your way around the entire area to make sure you apply an even polish. Take an ordinary household spray bottle and lightly mist the powder with water. If you do not have access to a polisher, you can apply your marble polish with a soft rag; however, this method is very tiring. Use a circular motion with steel wool to remove hard water buildup, then wipe with a clean water damp cloth. In between polishing, keep marble looking its best by dusting it with a dry mop or cloth, and cleaning up spills immediately. You have to make sure the top dust is buffed off and then seal the spot so that new dust doesn’t accumulate in it. We are looking for guest articles / blog post for our two cleaning blogs. Sorry, but we do not have knowledge of cultured marble products. By using talc or chalk alone, without smoothing out scratches and deeper abrasions, it would take hours and hours of polishing with talc to see any measurable difference in shine, because it is too soft. If interested, please look for a local stone professional and obtain an estimate for this service. As you may know, vinegar is an acid and will react with calcium based stone, dulling the polish and shine. Water is merely the medium that allows a buffer to distribute the tin oxide over the marble’s surface creating the shine. Only work on one small section of 1-2 feet at a time to create an even finish and avoid having your polishing compound dry out or begin to clump up. When you finish with the flat sides, polish the corners with a soft rag, continuing your circular movements. Avoid using or placing anything on your marble until it has completely dried because the seal needs time to set. If you’re using a polisher, slowly move it in a controlled circular motion. Another thing to know about marble polishing is “less is more”.

Dab the paste onto the stain, and cover it with plastic wrap. Working in small sections also helps you evenly distribute the polish because you are able to add small amounts of polish as you go.

Use a dry cloth to wipe away the residue, and then finish with a damp cloth to ensure a clean surface. After 24-48 hours, remove the plastic, pour a little water over the dry poultice, and wipe it away with a soft cloth. Fortunately, there are commercial products available for restoring marble either using polishing waxes (for floors in good condition), or mild polishing pastes that finely smooth out marble and add waxes and conditioners to effect the shine of dull marble. Yes, use a silicone spray cover with a good coat and let dry for two hours, then polish with a camel cloth. After your sealant has been on the marble for the recommended time, use a dry cloth to wipe the surface dry.

Depending on the surface condition of your marble, a single application polishing may not be enough to get the highest gloss on the first pass. If you have stains, try removing them with just your detergent by gently working the area with your damp cloth over the stain. Polishing your marble will not remove the stains; instead, you will be sealing them in. For best results, apply powder only to the dull area and not over the entire surface. If your marble is surrounded by other surfaces such as wood or chrome that could be damaged by the products you will use, protect them with painter’s tape.

You don’t need to seal marble in a shower unless you plan to use products that stain. Wipe the entire area with the chalk-covered sponge, applying more chalk when necessary. You can add water to the sealant by spraying on water or dabbing with a damp cloth. A sealant won’t prevent all stains, but will provide some protection to your marble surface. Countertops and vanities are usually sealed with an impregnator, while floors and other types of marble may be better served by a topical sealant.

Most marble used for building materials is in the hardness range of ‘4-6’, while some may be as soft as ‘3’. Personal care products don’t stain marble unless they’re allowed to sit. If you have stains, remove them with a poultice before polishing. Topical sealants sit on top of the marble and prevent staining, while impregnators go below the surface and repel water and oils while still allowing the marble to breathe. While you can use either, it takes longer to use a soft cloth, and if you do not keep up the same level of pressure it could affect your results, so a low-speed polisher might be your best bet. It is recommended to use a professional marble fabricator to make repairs, as they use oxcylic acid to repolish the surface to a factory finish. Smooth the poultice onto the stain and seal it by taping plastic wrap over it. Work the powder into the stone by using measured circular motions with either a clean, slightly damp cloth or with a polishing pad on an orbital buffer. With a little time and elbow-grease, you can polish your natural or cultured marble and make it look new again.

Do not apply polishing compound to the entire piece of marble at once. Put the compound on the small section where you will begin work. If baking soda is bad for teeth, why do some suggest using it on marble, another calcium based stone?
Source: www.stoneproonline.com/productcategory/polishing-products/
Source: www.wikihow.com/Polish-Marble
genaMarble
Wet sand area with a small sanding block in circular motions until smooth, then move to 600 grit and repeat. As you spray on your sealant, make sure that the entire surface of your marble is wet. You could also use a silicone spray when you’re done to help...